Find the right method for your bracelet: adjust the extender on our one-size women’s bracelets, choose a total length for leather and elastic designs, or compare the inside diameter of an open bangle. Every listed bracelet length includes the clasp.
Our women’s bracelets have an extension chain. Choose the design you like, then fasten it at the position that feels comfortable within that model’s adjustment range.
Open the clasp and wrap the bracelet around the wrist where you intend to wear it. Attach the clasp to a link on the extension chain that leaves comfortable movement without feeling tight. Check the fit with your wrist relaxed and when you bend your hand.
A 16 cm base with a 3 cm extender gives a nominal 16–19 cm total bracelet range, including the clasp. The extender changes the fastening position; it does not mean the bracelet fits every wrist. Check the model’s stated range if you are buying for someone else.
Essence is one size: 16 cm plus a 3 cm extender. Its lobster clasp can fasten along the extension to change the fit. This is an adjustable women’s bracelet, so there is no need to select a separate 18 or 20 cm variant.
Other designs can have a different range: Charisma is listed at 15 cm plus a 3 cm extension. Use each product’s own measurements rather than treating one example as the measurement for the entire collection.
Essence shown worn on the wrist. The extender allows the wearer to adjust where the bracelet closes. Aim for comfortable movement, with enough space for the flat chain to rest naturally.
For fixed-length and elastic bracelets, start with your wrist circumference. For women’s one-size designs, adjust the extender within the listed range. For open bangles, use the inside-diameter comparison below.
Wrap a flexible measuring tape around the place where you normally wear your bracelet. Keep it against the skin without pulling it tight or leaving a gap. Read the circumference in centimetres. If you use a paper strip or non-stretch string, mark the overlap and measure it flat with a ruler.
Record the wrist measurement itself before adding room for fit. If you add allowance while measuring and then add it again later, the bracelet will be too loose.
A single-wrap bracelet uses total bracelet length, including the clasp. A double-wrap bracelet passes around the wrist twice, so its full end-to-end length must be divided by two before you compare one wrap with the wrist. Elastic 18/20 cm styles also use total length.
Bangles use a different measurement: their listed 55/60/65 mm options refer to inside diameter. Do not compare those millimetres directly with wrist circumference or bracelet length.
Use this calculation when selecting a fixed total length, such as a men’s leather bracelet. For our women’s one-size bracelets, use the extender section above to check and adjust the available range.
Measure your wrist, then add the allowance for the fit you prefer. Example: an 18 cm wrist corresponds to a 19.5 cm bracelet for a regular fit.
Close fit: wrist + 1 cm. Regular fit: wrist + 1.5 cm. Relaxed fit: wrist + 2–2.5 cm. These are the starting allowances in our new guide.
A thick leather bracelet can feel closer than a slim chain of the same listed length. The clasp should meet and close naturally. Do not stretch leather or force a magnetic fastening to make a smaller size work. If the calculated length is between available sizes, compare the resulting allowance for both sizes and the feel you want.
| Preferred fit | Add to wrist | Total bracelet length |
|---|---|---|
| Close | 1 cm | 19 cm |
| Regular | 1.5 cm | 19.5 cm |
| Relaxed | 2–2.5 cm | 20–20.5 cm |
All lengths include the clasp. Select a size actually offered for the chosen product.
Silvus shows how to choose a fixed total length from a wrist measurement. Its clasp is already included in the listed size.
Men’s fixed-length leather bracelet. Silvus has a magnetic stainless steel clasp and listed 17.5–22.5 cm lengths. An 18 cm wrist plus 1.5 cm regular allowance gives a 19.5 cm choice.
Check that exact option on the product page. The clasp is already included in the 19.5 cm length. It should align naturally without pulling the leather tight. Protect the leather from water as described on the product page.
A double-wrap bracelet makes two turns around the wrist. The fit allowance applies to each turn.
For a regular fit, total bracelet length = 2 × (wrist circumference + 1.5 cm). The total length includes the clasp.
From wrist to bracelet: add the allowance to your wrist measurement and multiply by two. A 17 cm wrist plus 1.5 cm gives 18.5 cm per wrap; twice that is 37 cm total.
From bracelet to wrist: divide the full length by two, then subtract the allowance. A 37 cm bracelet gives approximately 18.5 cm per wrap; subtracting 1.5 cm points to a 17 cm wrist. For close fit use 1 cm per wrap; for relaxed fit use 2–2.5 cm per wrap.
| Wrist circumference | Length per wrap | Total bracelet length |
|---|---|---|
| 17 cm | 18.5 cm | 37 cm |
| 18 cm | 19.5 cm | 39 cm |
| 19 cm | 20.5 cm | 41 cm |
| 20 cm | 21.5 cm | 43 cm |
| 21 cm | 22.5 cm | 45 cm |
These figures refer to full physical bracelet length. Do not halve a wrist-size label or an already-converted per-wrap value.
Suprema is a double-wrap leather bracelet with a magnetic stainless steel clasp and fox-logo engraving. Use the full end-to-end length, including the clasp, for the double-wrap calculation above.
If your selected option does not state the full double-wrap length, ask us to confirm the corresponding total before ordering. Do not halve an option label without knowing which measurement it represents. The leather should be protected from water.
A figure that represents wrist fit or one wrap cannot be used as though it were the full length of a two-wrap bracelet. First establish the actual total, then use the chart.
This is particularly important when comparing a bracelet you already own with another model. Lay the double-wrap bracelet out fully and include its fastening in the measurement. Do not measure only the loop while it is wrapped.
For our elastic bead bracelets, your wrist should be approximately 1–1.5 cm smaller than the stated bracelet length.
Obsidius is an elastic lava-stone bead bracelet with a fox-head detail and stainless steel metal components. Its 18 and 20 cm options describe total bracelet length.
Use 18 cm as the starting choice for an approximately 16.5–17 cm wrist, or 20 cm for approximately 18.5–19 cm. Stretch is useful for putting it on, but the bracelet should not stay pulled tight around the wrist.
Do not treat the two suggested wrist ranges as a promise of fit for every wrist. A larger size will leave more room; a smaller one will leave less. The beads and your preferred feel also matter.
If neither option provides the allowance you want, consider an adjustable chain or another model with more length choices. Use the elastic rule here rather than automatically applying the relaxed single-wrap allowance.
| Listed total length | Suggested wrist circumference | Allowance |
|---|---|---|
| 18 cm | 16.5–17 cm | 1–1.5 cm |
| 20 cm | 18.5–19 cm | 1–1.5 cm |
The stated 18 or 20 cm is bracelet length, not the wearer’s wrist size.
Measure the inside of a well-fitting open bangle, across its widest internal span. Keep the ruler straight and exclude the metal on both sides.
| Millimetres | Centimetres |
|---|---|
| 55 mm | 5.5 cm |
| 60 mm | 6 cm |
| 65 mm | 6.5 cm |
55 mm = 5.5 cm · 60 mm = 6 cm · 65 mm = 6.5 cm. Diagram shows relative sizes; it is not a print-to-scale sizing tool. Diameter is not circumference.
Akitsune open bangles come in 55, 60 and 65 mm inside diameters. These millimetre sizes describe the internal width across the bangle, not wrist circumference or total bracelet length.
Ferus is an open stainless steel bangle with 55, 60 and 65 mm size options. These are inside diameters, not wrist circumferences. Compare the inside width of a comfortably fitting open bangle of similar shape.
The product allows gentle, careful adjustment. Choose the appropriate starting size rather than relying on repeated bending to make an unsuitable size work.
Use a comfortable open bangle as your reference. Lay it flat and measure straight across the inside, from inner edge to inner edge, without including the metal thickness. Compare that measurement with 55, 60 or 65 mm.
An open bangle also has an opening and a shape that affect fit. Do not convert a wrist circumference directly into one of these sizes or assume a universal wrist range. Ferus allows gentle, careful bending; choose the closest comfortable base size rather than relying on repeated bending to correct the wrong size.
Yes. For women’s one-size bracelets, adjust the extension chain within the product’s stated range. For fixed-length leather and rope bracelets, use wrist measurement plus a comfort allowance. Elastic bracelets use total length, while open bangles use inside diameter. Choose the method by construction, not gender alone.
Yes. Our listed bracelet lengths include the clasp. Do not add the fastening length on top of the stated size.
No. Halve only its confirmed full end-to-end length including the clasp. Do not halve a wrist-size label or an already-converted per-wrap size.
No. Our 18 cm figure is total bracelet length. The recommended starting wrist range is approximately 16.5–17 cm, leaving 1–1.5 cm of room.
Measure the recipient’s wrist if possible or compare a comfortable bracelet of the same construction. Keep total length, wrist circumference and bangle diameter separate. If the necessary measurement is unknown, ask before selecting a fit-sensitive gift.